Recab UK

Kontron CP3010-SA - 3U CompactPCI Intel Atom E38xx SBC

Key Features

32-bit 4/8HP CompactPCI® system slot
Intel® Atom™ E3845 or E3827 (Baytrail)
Up to 8GB soldered DDR3L
CFast and onboard SATA flash options
2 SATA interface via rear I/O, VGA, USB
CAN, 1 UART, multiple Ethernet channels
Up to -40 to +85°C fanless operation

Download Kontron CP3010-SA Datasheet
Download Kontron CP3010-SA Manual

Kontron CP3010-SA

3U CompactPCI Intel Atom E38xx SBC

Manufacturer: Kontron

Introduction

The CP3010-SA Kontron's latest low-power 3U CompactPCI® CPU board supports the Intel® Atom™ processors E3826 and E3845 with a maximum of quad-core 1.91 GHz processing performance. Even though the board design is based on Atom™ technology, performance levels of former Core™ 2 Duo platforms can be reached. Further, the built-in graphics core now features Intel® HD Graphics Technology offering an outstanding increase in graphics performance compared to previous Atom™ designs.

Memory demanding applications can make use of up to 8GB soldered DDR3L running at 1333MHz. For onboard data storage, the CP3010-SA offers a CFAST option or a soldered SATA Flash and an HDD/SSD option on the 8HP extension module.

CPU
CPU Spec	Intel® Atom™ SOC (22nm technology): E3845: Quad-Core 1.91 GHz, 2MB cache E3827: Dual-Core 1.75 GHz, 1MB cache
Chipset	Integrated
Memory	Up to 8GB soldered DDR3L running at 1067/1333 MHz, dual channel w/o ECC
Graphics	Intel® Gen7 Graphics, OpenGL 3.0, OpenCL 1.2, DX11, H.264, MPEG2, MCV, VC-1, VP8
Network	Up to three 1000BASE-T interfaces with WOL (Wake-on-LAN) support, two front/rear switchable, third available via 8HP extension, Intel® I210-IT Ethernet controller
Storage	Onboard CFast installation via CFAST module Up to 64GB soldered SATA NAND Flash, optional available Onboard 2.5" SATA SSD/HDD installation via 8HP extension Two SATA 3 Gb/s ports via rear J2
Front I/O	Front Interfaces 4HP • DisplayPort: 2x 20-pin DisplayPort connectors, DVI/HDMI/VGA capable through cable adapter • USB: 1x USB 3.0 port, 9-pin type-A connector, 1x USB 2.0 port, 4-pin type-A connector • Ethernet: 2x RJ-45 with integrated LEDs (ACT, SPEED) • LEDs: 6x LED’s: 4x POST Code or General Purpose, WD, TH Front Interfaces 8HP (additional to 4HP) • Ethernet: 1x RJ-45 with integrated LEDs (ACT, SPEED) • CAN: 1x 9-pin D-Sub connector • Serial Port: 1x 16C550-compatible serial port, RS-232 signalling, RJ-45 • USB: 1x USB 2.0 port, 4-pin type-A connector • Line-In: 1x 3.5 mm stereo jack, bluejack • Line-Out: 1x 3.5 mm stereo jack, green jack • Control: Reset button and HDD activity LED
Rear I/O	Rear I/O via J2 The CP3010-SA supports the following interfaces via Rear I/O: • One VGA analogue port • Two USB 2.0 ports • Two Gigabit Ethernet ports without LED signals • Two SATA 3 Gb/s ports • Two COM ports RS-232 (LVTTL signal level) • Five GPIs and Three GPOs (LVTTL signal level) • System management signals: Power Button, Sleep S3, 5V Standby • Option to write protect non-volatile RAMs via a special pin
Other	High-Speed Extension Connector • One 60-pin high-speed connector holding: • COMA (TTL) • One SATA 3Gb/s • One USB 2.0 • PCIe x1 • HDA • XBUS • Reset Hot Swap: Support for all signals to allow peripheral boards to be hot swapped. The individual clocks for each slot and access the backplane ENUM# signal comply with the PICMG 2.1 Hot Swap Specification
BIOS	Two redundant 8 MB SPI boot flashes with fail-over functionality Phoenix UEFI, setup console redirection to a serial port (VT100 mode) with CMOS setup access, EFI Shell support, board configuration via Shell, diskless, keyboardless, videoless operation
Options	Watchdog: FPGA-based, timeout ranging from 125ms to 4096s programmable in 16 steps, IRQ, reset, dual-stage configuration RTC: Integrated into SOC Trusted Platform Module (TPM): Atmel AT97SC3204 TPM 1.2 controller CAN: SJA1000 CAN controller for one CAN port, available on the 8HP extension

GENERAL
Expansion	PICMG 2.0 Rev. 3.0 compatible, 32-bit/33MHz (66MHz on request), version with rear I/O via J2 Universal 5V and 3.3V PCI signalling voltage supported, 7 Req/Gnt & clock lines Operating in system slot as system master and in a peripheral slot in PCI passive mode CompactPCI® Core Specification PICMG 2.0 Rev. 3.0 CompactPCI® Hot Swap Specification PICMG 2.1 Rev. 2.0
Electrical	Supply voltage/power consumption: • +5.0V (4.85 V min. to 5.25 V max) • +3.3V (3.2 V min. to 3.47 V max) • +5.0V STDBY (optional, 4.85 V min. to 5.25 V max) • Intel® Atom™ E3845 1.91 GHz: 14.3W max, 9.4W typical, 7.8W idle • Intel® Atom™ E3827 1.75 GHz: 11.6W max, 8.6W typical, 7.8W idle
Mechanical	Dimensions: conforming to CompactPCI® specification for 3U boards Front panel: 4HP or 8HP with ejector
Conformal Coating	on request
Software	Support for Windows® 7, Windows® Embedded Standard 7, Windows® 8, Linux, VxWorks®, QNX®
Temperature	Temperature range (operation): • 0 to +60°C standard • -40 to +85°C extended temperature E2 Temperature range (storage): -40 to +85°C
Humidity	93% RH at 40°C, non-condensing (acc. to IEC 60068-2-78)
Weight	4HP: ca. 350g
Warranty	2 Years
RoHS	Compliant

ORDERING DETAILS
Board	CP3010-SA-1.91Q-4-4F-T Atom™ E3845, 1.91 GHz, 2MB cache, 4GB DDR3L, 4HP, Front I/O CP3010-SA-1.91Q-4-4R-T Atom™ E3845, 1.91 GHz, 2MB cache, 4GB DDR3L, 4HP, Rear I/O CP3010-SA-1.91Q-4-8F-T Atom™ E3845, 1.91 GHz, 2MB cache, 4GB DDR3L, 8HP, Front I/O, HD/SSD/CFast Carrier CP3010-SA-1.75D-4-4F-T Atom™ E3827, 1.75 GHz, 1MB cache, 4GB DDR3L, 4HP, Front I/O CP3010-SA-1.75D-4-4F-T-E2 Atom™ E3827, 1.75 GHz, 1MB cache, 4GB DDR3L, 4HP, Front I/O, ext. Temp.
Accessories	CP-RIO3-04 4HP rear I/O module (2x Ethernet, 2x USB, VGA, 2x SATA connectors) CP-RIO3-04 8HP rear I/O module (additional to 4HP COMA/B) CP-RIO3-04S 4HP rear I/O module (2x Ethernet, COM, VGA, 2x SATA connectors)

Key Features

Kontron CP3010-SA

3U CompactPCI Intel Atom E38xx SBC

Introduction

CPU

GENERAL

ORDERING DETAILS

Related Products

Kontron CP3005-SA

Kontron CP3004-SA

Kontron CP342

Kontron CP347

Interested in this Product?

Ordering

Support

Contact Us